RAMPS 1.57 Control Board LCD 2004 Board Mega 2560 R3 A4988 Driver Kit
Tax included.
RAMPS 1.57 Control Board LCD 2004 Board Mega 2560 R3 A4988 Driver Kit For 3D Printer
We will default sending carton package to replace the plastic box, but there may some stocks are still packaging with plastic box, please note about this before you buy it.
RAMPS 1.57 Control Board: (Single buy, click here)
Introduction:
This product is an Arduino MEGA as Ultimaker UltiStepper drive is compatible with Pololu stepper driver boards. It is very similar to other electronic Pololu based implementation, including RAMPS, and it can support up to five stepper motors (three for the X, Y, Z, a function of one of the other extruder). You can add as much as you need stepper drive carriers. It is designed to run at a higher voltage than 12 volts, which allows you to put a 90-watt MOSFET and run your stepper motor with more torque and higher top speed. It has a head, increasing the SD card module, IDC header add LCD panel (movie), PWM output power LED arrays and other lighting and serial I / O, Bluetooth and Ethernet add-ons.
Note: Connect Jumper (nearly VR tube 7812TV), Arduino MEGA Ultimaker control panel will also have the power.
Feature:
Simple 4-way JST connector plug for all motors.
Stepper motor control up to five (X, Y, and Z-axis extruder (the "E-axis"), optionally can be added by adding a second shaft Pololu stepper drive.
Step will be configured via jumpers.
3 times 55 amps MOSFET output (with LED indicator. Actual current limited capacity PCB and connector)
All leads are breaking the maximum scalability from 15V to 19V.
Thermocouple input, or thermistor input. 100K thermistor recommendations.
Power on / switch at documented board.
Thermocouple wiring easier.
(Normally open) fan-cooled electronic device includes a 12V regulator.
Now LCD backlight dimming can be controlled by software.
Support double print
A4988 driver:
Low RDS (ON) outputs
Automatic current decay mode detection / selection
Mixed with slow current decay mode
Synchronous rectification for low power dissipation
Internal UVLO
Crossover current protection
3.3 and 5V compatible logic supply
Thermal shutdown circuit
Ground short circuit protection
Load short-circuit protection
Five selectable stepper modes: full, 1/2, 1/4, 1/8 and 1/16
Package included:
1 x RAMPS 1.57 Control Board
1 x LCD 2004 Control Board
5 x A4988 Driver
1 x Mega 2560 R3 Development Board
1 x USB
2 x FC-10P flat cable
We will default sending carton package to replace the plastic box, but there may some stocks are still packaging with plastic box, please note about this before you buy it.
RAMPS 1.57 Control Board: (Single buy, click here)
Introduction:
This product is an Arduino MEGA as Ultimaker UltiStepper drive is compatible with Pololu stepper driver boards. It is very similar to other electronic Pololu based implementation, including RAMPS, and it can support up to five stepper motors (three for the X, Y, Z, a function of one of the other extruder). You can add as much as you need stepper drive carriers. It is designed to run at a higher voltage than 12 volts, which allows you to put a 90-watt MOSFET and run your stepper motor with more torque and higher top speed. It has a head, increasing the SD card module, IDC header add LCD panel (movie), PWM output power LED arrays and other lighting and serial I / O, Bluetooth and Ethernet add-ons.
Note: Connect Jumper (nearly VR tube 7812TV), Arduino MEGA Ultimaker control panel will also have the power.
Feature:
Simple 4-way JST connector plug for all motors.
Stepper motor control up to five (X, Y, and Z-axis extruder (the "E-axis"), optionally can be added by adding a second shaft Pololu stepper drive.
Step will be configured via jumpers.
3 times 55 amps MOSFET output (with LED indicator. Actual current limited capacity PCB and connector)
All leads are breaking the maximum scalability from 15V to 19V.
Thermocouple input, or thermistor input. 100K thermistor recommendations.
Power on / switch at documented board.
Thermocouple wiring easier.
(Normally open) fan-cooled electronic device includes a 12V regulator.
Now LCD backlight dimming can be controlled by software.
Support double print
A4988 driver:
Low RDS (ON) outputs
Automatic current decay mode detection / selection
Mixed with slow current decay mode
Synchronous rectification for low power dissipation
Internal UVLO
Crossover current protection
3.3 and 5V compatible logic supply
Thermal shutdown circuit
Ground short circuit protection
Load short-circuit protection
Five selectable stepper modes: full, 1/2, 1/4, 1/8 and 1/16
Package included:
1 x RAMPS 1.57 Control Board
1 x LCD 2004 Control Board
5 x A4988 Driver
1 x Mega 2560 R3 Development Board
1 x USB
2 x FC-10P flat cable