3.7V DIY Transistor Graphic Tester LCD Digital Multimeter Diode Inductor Capacitor ESR Meter + Shell
Tax included.
Description:
The tester uses 3.7V rechargeable lithium battery (battery model: 14500) powered portable design, but you can use the T-MINIUSB outlet to charge the battery and power the system for a long time in the indoor use of more economical and convenient, eliminating the need always to be replaced battery of economic input.
Features:
1. One key measurement operation, auto power off delay. Shutdown current is only 20nA, support for battery operation.
2. Automatic test PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET FET, diodes, two diodes, thyristors, resistors, capacitors, inductors.
3. Automatic test pin definitions.
4. Measuring the current amplification factor (B) of the bipolar transistor and the turn-on voltage of the emitter junction (Uf).
5. Darlington transistor amplification factor can be identified by the high threshold voltage and high current.
6. It can te bipolar transistors and MOSFET's internal protection diodes and displayed on the screen.
7. Measuring the threshold voltage and the gate capacitance of the MOSFET.
8. Support two resistance measurements, the potential can be measured. If the potentiometer is adjusted to its end, the tester can not distinguish between the middle and the ends of the pin.
9. Resistance measurement resolution is 0.1 ohms, the maximum value of 50M ohms measurements. Capacitance measurement range from 25pf to 100mF (10 UF).
10. Resolution up to 1 pF, inductance measurement range 0.01MH-20H, otherwise it will appear as a resistor, inductor DC resistance is higher than if Europe 2100 will also be displayed as a resistor.
11. Can test 2UF above capacitor equivalent series resistance (ESR), a resolution of 0.01 ohms.
12. This feature is very important for the test of the capacitor performance.
13. Can display symbols of the two diodes in the right direction, also shows the forward voltage drop.
14. LED test for diode forward voltage drop higher than normal. Dual LEDs tested as double diode.
15. Simultaneous test of light-emitting diodes will flash. Time for each test is about two seconds, only the large capacitance and inductance measurements will take a long time.
Correction:
Short three test side, into the test, the screen prompts correction step. When prompted to disconnect the short end of the calibration time off three tests will continue. When prompted in the 1-3 foot access 100nF capacitor over time, access to distribution after correction capacitors 1uF program will automatically enter the next step. Correction until the end of the restart to complete the correction.
The main parameters and use:
1. Using AT ATmega328 micro controller.
2. 2x16 character LCD display results.
3. One-button operation, automatic power off.
4. Shutdown current of only 20nA, support for battery operation.
5. Low-cost version without the crystal, auto power off. 1.05k version of the software ATmega168 or ATmega328 in sleep mode when no measurement to reduce power consumption.
The tester uses 3.7V rechargeable lithium battery (battery model: 14500) powered portable design, but you can use the T-MINIUSB outlet to charge the battery and power the system for a long time in the indoor use of more economical and convenient, eliminating the need always to be replaced battery of economic input.
Features:
1. One key measurement operation, auto power off delay. Shutdown current is only 20nA, support for battery operation.
2. Automatic test PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET FET, diodes, two diodes, thyristors, resistors, capacitors, inductors.
3. Automatic test pin definitions.
4. Measuring the current amplification factor (B) of the bipolar transistor and the turn-on voltage of the emitter junction (Uf).
5. Darlington transistor amplification factor can be identified by the high threshold voltage and high current.
6. It can te bipolar transistors and MOSFET's internal protection diodes and displayed on the screen.
7. Measuring the threshold voltage and the gate capacitance of the MOSFET.
8. Support two resistance measurements, the potential can be measured. If the potentiometer is adjusted to its end, the tester can not distinguish between the middle and the ends of the pin.
9. Resistance measurement resolution is 0.1 ohms, the maximum value of 50M ohms measurements. Capacitance measurement range from 25pf to 100mF (10 UF).
10. Resolution up to 1 pF, inductance measurement range 0.01MH-20H, otherwise it will appear as a resistor, inductor DC resistance is higher than if Europe 2100 will also be displayed as a resistor.
11. Can test 2UF above capacitor equivalent series resistance (ESR), a resolution of 0.01 ohms.
12. This feature is very important for the test of the capacitor performance.
13. Can display symbols of the two diodes in the right direction, also shows the forward voltage drop.
14. LED test for diode forward voltage drop higher than normal. Dual LEDs tested as double diode.
15. Simultaneous test of light-emitting diodes will flash. Time for each test is about two seconds, only the large capacitance and inductance measurements will take a long time.
Correction:
Short three test side, into the test, the screen prompts correction step. When prompted to disconnect the short end of the calibration time off three tests will continue. When prompted in the 1-3 foot access 100nF capacitor over time, access to distribution after correction capacitors 1uF program will automatically enter the next step. Correction until the end of the restart to complete the correction.
The main parameters and use:
1. Using AT ATmega328 micro controller.
2. 2x16 character LCD display results.
3. One-button operation, automatic power off.
4. Shutdown current of only 20nA, support for battery operation.
5. Low-cost version without the crystal, auto power off. 1.05k version of the software ATmega168 or ATmega328 in sleep mode when no measurement to reduce power consumption.