4 Button 433.92MHz Garage Gate Key Remote Control For Seip SKR433-1 SKRJ433 TM
Tax included.
Description:
4 Button 433.92MHz Garage Gate Key Remote Control For Seip SKR433-1 SKRJ433 TM
Specification:
Color: Black
Size(approx.): 58.8mm/2.31”(L) x 37.3mm/1.46” (W)
(Detail size as shown in the picture)
Material: Plastic and aluminum alloy
Frequency: 433.92MHz
Coding Type:Hopping
Battery : 3V CR2016(Lithium cell)
Code Number of Code Combinations: Over 4.29 Billion Random Codes
Size(approx.): 58.8mm/2.31”(L) x 37.3mm/1.46” (W)
(Detail size as shown in the picture)
Material: Plastic and aluminum alloy
Frequency: 433.92MHz
Coding Type:Hopping
Battery : 3V CR2016(Lithium cell)
Code Number of Code Combinations: Over 4.29 Billion Random Codes
Fitment:
(The Compatibility Is Just For Reference. Please Compare The Follows With Your Original One before Purchasing!)
Replaces Remote Models:
SEIP TM 60
SEIP TM 80
SEIP TS 75
SEIP TS 100
SEIP SKR433-1
SEIP SKRJ433
Gryphon Stealth
How to copy the original remote(for reference only)
Method 1
(use this procedure only if you have an existing working midi keyfob transmitter with four buttons and a Seip model A45, A60, C75 or C100 operator)
1. Briefly depress the two lower buttons on the original handset simultaneously, a beeping sound should now be heard from the motor unit to indicate that the receiver has entered into 'code learning mode'
2. Take the new midi keyfob and press the button that you wish to use to operate your door and hold briefly
3. Your new handset should now operate your garage door.
Note :If you have more than one Seip motor in your garage it will be necessary to switch off the power to each motor in turn to avoid both receivers entering the 'code learning mode' together, or use method 2
Method 2
If you are unable to use method 1 above because you don't have an original working keyfob with four buttons or you have a Seip model M50 operator it will be necessary to release the fixing screw at the rear centre of the motor casing and open the hinged cover and proceed as follows :
1. Locate the programming button on the decoder PCB inside the motor casing, (see photo right) and press it briefly (a yellow LED will flash on the decoder PCB or a bleeping sound will be heard), you have 10 seconds to perform the next step.
2. Take the new handset and press the button that you wish to use to operate your door for one second.
3. Your new handset should now operate your garage door.
(Note: the Seip receiver modules type WAM1K & WAK1K have a small black programming button on the casing)
Clearing the memory - (recommended if a handset has been lost or stolen)
Refer to Method 2 above but at step 1. press and hold the programming button
for 20 seconds then follow steps 1, 2 & 3 to re-program your remaining keyfobs
(The Compatibility Is Just For Reference. Please Compare The Follows With Your Original One before Purchasing!)
Replaces Remote Models:
SEIP TM 60
SEIP TM 80
SEIP TS 75
SEIP TS 100
SEIP SKR433-1
SEIP SKRJ433
Gryphon Stealth
How to copy the original remote(for reference only)
Method 1
(use this procedure only if you have an existing working midi keyfob transmitter with four buttons and a Seip model A45, A60, C75 or C100 operator)
1. Briefly depress the two lower buttons on the original handset simultaneously, a beeping sound should now be heard from the motor unit to indicate that the receiver has entered into 'code learning mode'
2. Take the new midi keyfob and press the button that you wish to use to operate your door and hold briefly
3. Your new handset should now operate your garage door.
Note :If you have more than one Seip motor in your garage it will be necessary to switch off the power to each motor in turn to avoid both receivers entering the 'code learning mode' together, or use method 2
Method 2
If you are unable to use method 1 above because you don't have an original working keyfob with four buttons or you have a Seip model M50 operator it will be necessary to release the fixing screw at the rear centre of the motor casing and open the hinged cover and proceed as follows :
1. Locate the programming button on the decoder PCB inside the motor casing, (see photo right) and press it briefly (a yellow LED will flash on the decoder PCB or a bleeping sound will be heard), you have 10 seconds to perform the next step.
2. Take the new handset and press the button that you wish to use to operate your door for one second.
3. Your new handset should now operate your garage door.
(Note: the Seip receiver modules type WAM1K & WAK1K have a small black programming button on the casing)
Clearing the memory - (recommended if a handset has been lost or stolen)
Refer to Method 2 above but at step 1. press and hold the programming button
for 20 seconds then follow steps 1, 2 & 3 to re-program your remaining keyfobs
Package includes:
1 x Remote(with battery)
Details pictures:
